Skip to content
Ring (562) 647-6550

Guide ยท Whittier

Garbage disposal installation service

Replacing or adding a disposal is a plumbing and electrical job in one sink cabinet. This page explains what an installation visit covers, published cost ranges, the extras that change the price, and what to ask before you book.

Last changed

Under-sink disposal below the sink flange, with a drain outlet, dishwasher inlet and drain pipe.

A typical visit swaps out the old disposal, hangs the new one from the sink flange, hooks up the trap and dishwasher hose, handles the power connection and checks for drips. One published guide prices the whole thing, unit included, from $150 to $950, averaging $400 to $500. Related kitchen topics are gathered under faucets, sinks, showers and disposals.

What happens during a removal and installation visit?

The plumber takes out the old unit, cleans the sink flange, mounts the new disposal, reconnects the trap and the dishwasher inlet, and runs a test. Where none existed, a flange goes in and a switch and power may be added. Items like a power cord or baffle can be extra.

A swap can often reuse the mounting ring and flange, which shortens it. A first-time install runs longer, since the sink opening, the drain and the wiring may all need changes. One classic miss: the dishwasher knockout plug inside the new disposal must be punched out if the dishwasher drains through it, or the dishwasher backs up.

Pin down the quote's contents: hauling the old unit away, new fittings, and a test run are all worth confirming.

What does disposal installation usually cost?

This Old House reports $400 to $500 on average for the unit plus installation, within an overall span of $150 to $950. Unit price follows horsepower and feed type; labor follows swap versus first-time install. Treat these as national guide numbers and not a quote for any particular kitchen.

Disposal size or feed type Published unit price
1/3 HP $75 to $150 (another listing $100 to $200)
3/4 HP $100 to $250
1 HP $200 to $500
2 HP $300 to $1,000
Continuous feed $75 to $500
Batch feed $200 to $650

Hourly labor in that guide: $50 to $75 for a handyperson, up to $150 for a plumber, $50 to $120 for an electrician when wiring is involved. Doing a faucet and a disposal in one go cost $410 to $1,300. Small extras accumulate: a push-button switch kit around $40, a baffle for $5 to $13, a dishwasher drain connector for $9 to $15.

Why do two installations cost different amounts?

Five things mostly: the unit, swap or first install, the electrical situation, the state of the sink and drain, and the labor rate. Adding a switch or outlet, or reshaping a sink opening, takes time, and so does a crowded cabinet.

Start with size. Small motors (1/3 or 1/2 horsepower) cope with everyday scraps; bigger ones cost more, run quieter and jam less. Batch-feed units start only when the stopper is twisted in and price higher than continuous-feed ones. Mount designs vary, and a unit that fits the old mount saves labor.

Wiring is the surprise line item. Plugging into an outlet under the sink is simple, while hardwiring or adding a switch needs an electrician or a plumber comfortable with it. The guide above lists an electrician at $50 to $120 an hour.

If the sink or drain is old, corroded fittings can add parts and time.

Is this a reasonable weekend project?

For a like-for-like swap, plenty of handy people say yes. Cut power at the breaker, unhook the old unit, hang the new one, reconnect drain and dishwasher hose, restore power and test with water running. A first installation that involves wiring, a switch or new plumbing is better handed over.

Water plus electricity in a tight cabinet is the hazard. Never work with power on, and never reach into the grinding chamber; use the hex wrench socket on the underside, or tongs. After the first run, inspect the flange, trap and dishwasher hose for drips.

Licensing: California wants a contractor license for work reaching $1,000 in labor and materials or needing a permit. A disposal swap typically falls below that, though permit rules differ between cities and building types, so the building division can confirm. Mobile home alterations are regulated by the state housing agency, HCD; check with it first.

Repair or replace the disposal?

A unit that hums without spinning, trips its reset or drips only at a hose joint may be cheaper to repair or clear. Replacement wins when the housing itself leaks, the motor is dead, or an old unit keeps jamming. An on-site look settles which.

Decision flow: a humming disposal is cleared and reset, while a leaking housing means replacing it.

Repairs ran $50 to $400 in that guide. Start with basics: press the reset button underneath, free a jam with the hex wrench, clean out the drain. Step-by-step help is in unclogging a garbage disposal drain and clearing a kitchen sink.

A clog that keeps returning may sit in the sink drain or beyond rather than in the disposal, so have the whole drain checked and not just the unit.

Which questions belong on the booking call?

Cover these points: what the price includes, whether the unit itself is quoted or only labor, how the wiring will be done, whether the old disposal gets hauled away, the expected visit length and who deals with any permit. Collect written answers from at least two sources.

Ready to have it looked at? A price request lines up a local plumber. Prices for a neighboring job appear in plumber install faucet cost, and fixing a leaky faucet helps if the tap needs attention too. The home page has our other services.

Common questions

How long is a disposal installer on site?

A straight swap is generally brief, often under two hours, while a first-time installation with wiring or plumbing changes runs longer. Cabinet access and the state of old parts matter. Request a time estimate when you book so you can plan around it.

Which horsepower suits a household?

For a typical home, 1/3 to 3/4 horsepower copes with daily scraps. Big households or heavy use justify 1 horsepower or more, which costs extra but jams less and runs quieter. Choose by how you cook and by what the sink mount accepts.

Does the job need two trades?

Not necessarily. Where a switch and an outlet or hardwired connection already exist, a plumber can replace the unit. New circuits, switches or outlets are electrical work. Some plumbers do simple wiring and others bring an electrician, so ask who does what and whether one quote covers both.

Why is the dishwasher draining badly since the new disposal went in?

A knockout plug inside the dishwasher inlet may still be in place, which stops dishwasher water entering. Punch it out with a screwdriver and light hammer taps, then fish out the plastic piece. Kinks in the drain hose and a blocked air gap are the next things to check.

Should you add a disposal at all?

Many households like having one, but it needs cold water while running, and grease, fibrous peels and bones still belong in the trash. Make sure your drain and local rules suit one, and raise any doubts with the plumber during the visit.

References